Contact us
- : 0086-371-86151627 0086-371-86151827
- : 0086-371-86011881
- : [email protected]
- : [email protected]
- : bebonchina
Products- Boiler steels
- High carbon steel
- High Yield steel
- steel for welded tubes
- General construction steel
- steel with Cr.,Mo.,Cr-Mo
- Steel for large diameter pipes
- Simple pressure vessels steel
- Steel for gas cylinders and gas vessels
- General purpose structural steels
- Steel for boilers and pressure vessels
- steel resistant to atmospherical corrosion
- Carbon steel and low alloy steel
- Fine-grain structural steels,normalised rolled
- weldable normalized fine grained pressure vessel steels
News- Rolling points of HP265 Steel
- Causes of Wrinkles on the Surface of
- Advantages of Controlled Rolling for
- The difference between A283 Gr C and
- Quality inspection of plate A285 gra
- A285 Gr.C plate for storage tanks
- The processing Technology of NM400 S
- Possible defects of 16Mo3 steel plat
- Acceptance criteria of Surface for 1
- Heat Treatment and Applications of A
ASTM A514/A514M A514GrQ High yield steel plate
ASTM A514/A514M A514GrQ High yield steel plate
The technical conditions apply to plates of A514GrQ with thickness not more than 150mm. (8mm-150mm)
Adopt standard:
ASTM A514/A514M Standard Specification for High-Yield-Strength, Quenched and Tempered Alloy Steel Plate, Suitable for Welding.
Thickness tolerance: +/-1.52mm
Flatness: 4mm/m
Surface shot blasting or peeled.
The third party inspection:
The chemical composition, tensile test and Charpy -V impact test for plates of A514GrQ shall be witnessed by surveyor of ABS.
Delivery conditions
The delivery conditions for plates of A514GrQ shall be: Quenching +Tempering.
ASTM A514GrQ Chemical Composition:
C |
Si |
Mn |
P |
S |
Cr |
Ni |
Mo |
V |
B |
Ti |
Max 0.18 |
0.15- 0.35 |
0.95- 1.30 |
Max 0.020 |
Max 0.006 |
1.00- 1.50 |
1.20- 1.50 |
0.40- 0.60 |
0.030- 0.080 |
Max 0.005 |
Max 0.02 |
ASTM A514GrQ Mechanical properties:
Size(mm) |
Mechanical properties |
Lateral expansion |
Hardness test |
|||
1/4 T |
||||||
150 |
Yield strength MPa |
Tensile strength MPa |
Section shrinkage ratio % |
Elongation % |
mm |
HB |
Min 690 |
770-890 |
Min 50 |
Min 14 |
Min 0.38 |
230-290 |
|
A514GrQ steel plate Grain size:
No. |
Test item |
Quantity, Piece |
Direction |
Test method |
1 |
Hardness |
1 |
/ |
According to ASTM A370 |
2 |
Tensile test |
2 (per heat treatment pc) |
Transverse/ |
|
Longitudinal |
||||
3 |
Charpy-V impact test at -40C |
3 (per heat treatment pc) |
Longitudinal |
|
4 |
3 (per heat treatment pc) |
Longitudinal |
||
5 |
Gas analysis |
1 |
/ |
GB/T 14265 |
6 |
Nonmetallic inclusion |
1 |
/ |
GB/T 10561 |
BBN STEEL ASTM A514/A514M is a high strength tempered alloy steel plate. Mainly used for rack-lifting of jack-up offshore drilling platforms.